Same for me, VX1 uart + metr (when I can actually get one)
Shipping to Australia pretty pleaaase!! 
1 Like
Damn, was hoping to break out the other uart for osrr and robogotchi on my 100D.
1 Like
Similar use case: Vx2 then OSRR. Metr, davega or robogotchi.
Unfortunately Iām wayyyyy too busy to investigate. and already took the stormcore out of the rion. Going with lower kv motors and a 17s 75/200 until the rion vesc is 100 percent.
Iāll find a place for the 100d. Plenty of projects and donāt really care to deal with it. Keep up the good work. 
2 Likes
I feel this on a spiritual level.
4 Likes
You can order metr worldwide from my store if metr site dont have it
1 Like
I have some timeā¦would be glad to take it off your hands 
3 Likes
Where are my trampa wheels fool
3 Likes
Lol! In my closet. You around tommorow? I really need some 10s bmss lol
1 Like
Are there any timeframe updates as to when this will be available?
5 Likes
I checked Deutsche Post website and shipping to Australia/New Zealand is possible again. 
All open Metr Pro orders that werenāt refunded because of the long delay are shipped now.
I think Roman left a little hint. 
9 Likes
I can say when I run the Vesc Tool setup wizard, once it is complete I can turn off the Stormcore once, but the next time I turn it on it returns to this state of being unable to power off.
Let me know if you have thoughts or what additional information would help to diagnose this. Thanks in advance!
1 Like
I have a similar issue but only on my 4wd set up. They told me they would have a firmware fix for this sometime this weekend, we wait and see 
4 Likes
What would it take to get a tx and rx signal out of the can port? Thatās all I need for my remote and I really want to use the robogotchi in the uart without having to sacrifice the remote telemetry.
Any thoughts on if the stormcores might play nicely with the usplit by @ricco? Might be a nice way to help everyone out that needs more uartz
1 Like
Just seen the import tax and customs, hope I donāt get stung lol
Anyone know if the Bluetooth module built in can be used to link a remote or will I still need to hook up a dongle, I have a wand laying around, hoping itās just plug and play
1 Like
i guess it will works without trampaās dong
1 Like
I did get it to work with a wand. There were a few dropouts but that happened with the dedicated dongle also.
1 Like
Thanks guys, good to know, probably end up using a maytech v2, we will see
1 Like
I am working with Charles from Lacroix, as well about a maybe similar issue:
Right after triggering the e-stop pin on my 100D, the board could not turn off. I donāt even get a flicker of light. The 100D lights stay on (on the board) and the power button turns red and stays that way. Also, the 100D starts heating up significantly next to the power input (where the anti-spark circuit is located).
If I unplug and plug the power back in, it is still the same: stays on / red pwr switch / heating up. I can still get into the vesc app or the stormcore app, and they both show 38V, when my battery is actually 58V. Something is getting fried in our boards and I really believe that it is the antispark switches.
I just got my replacement 100D today, and everything was ok, until I triggered the e-stop pin and then the board died just like the first one. Obviously, if I knew that is what killed the first one, I would have never tried to activate the e-stop, but I have it on a scooter so I use the e-stop as an electronic lock.
Hopefully you get this fixed. I would love to know if your issue is the anti-spark circuit and if you might know how it got affected (like my e-stop sitiuation).
Thank you!
4 Likes