DAVEGA X: Gauging interest

janpom · September 13, 2019, 6:58pm

Getting ready for shipping. I had to call my loyal workers to service.

moon · September 13, 2019, 7:00pm

Brilliant

Mainflow · September 13, 2019, 7:01pm

I will order immediately, when the form is available.
Don’t let the kids be slaves!

Mainflow · September 13, 2019, 7:01pm

Do you have your katana ready?

drone001 · September 13, 2019, 7:02pm

sitting in front of my computer like a keyboard warrior…waiting on that order form I want my GA x…lol

mmaner · September 13, 2019, 7:11pm

I’m really looking forward to this. Visually it’s stunning, both the case and the UI. I’m sure it’s at a minimum as good quality as the OS version, so zero worries there.

I look forward to be able to order a couple. Good job as always @janpom.

pookybear · September 13, 2019, 8:04pm

I think I broke my refresh button.

janpom · September 13, 2019, 8:49pm

I only whip them occasionally.

pookybear · September 13, 2019, 8:50pm

@SeanHacker
@pundahh

Are guys running the latest firmware? V1.19?

I’ve ruled out:

Pin outs - even switched RC and tx
Reprogrammed DaVega
Master and slave UART port don’t work w DaVega using new firmware (1.19)
both uart ports work w BT metr pro module and trampa nrf.
DaVega works w older fw.
Using default 500Hz (app — general) like the old fw makes the red dot indicator flash as opposed to solid red using 50hz. Don’t know what this means but I do know flashing red dot means it’s receiving “signal”. Not an EE so this is way beyond my pay grade.

Metr shows telemetry on slave using 1.19 FW.

These are the results I have found so far.

SeanHacker · September 13, 2019, 8:56pm

I’m running

Because the newest firmware makes my boards feel weird.

mmaner · September 13, 2019, 8:57pm

Sounds like it is touching you in your private place

pookybear · September 13, 2019, 9:02pm

I’ll try to see if older FW works w the trampa wand.

pundahh · September 13, 2019, 9:16pm

I’m running ackmaniac 3.102 fw &. V1.01 on the davega

hexakopter · September 13, 2019, 9:31pm

Make sure to not confuse VESC firmware and VESC Tool version. VESC firmware is at V3.XX for a long time.
The newest VESC Tool version is 1.19 at the moment and the newest VESC firmware 3.61.

pookybear · September 13, 2019, 9:42pm

Yes. I’ll edit it my post

V1.19 equates to 3.61fw

janpom · September 14, 2019, 9:25am

This is the sexiest davega enclosure ever made! Well done @LR-designs!

glyphiks · September 14, 2019, 9:27am

It sure is! Where’s the form!?

Mainflow · September 14, 2019, 9:29am

Everyone asks here for that! I CAN’T wait. I need now.

b264 · September 14, 2019, 10:00am

You’ve got my attention now

metal > not-metal

janpom · September 14, 2019, 10:22am

I didn’t give enough credit to the raw until I installed it. It really shines on the board, despite the small scratches from machining that haven’t been covered by anodizing. I think I’m keeping that one.

BTW, raw housing will come with raw baseplate. I was just too lazy to change the baseplate for the picture.