Thanks a lot !!! Hooooo yes it is !
So easy to stress test elec. with handlebar
It always call me for :
Thanks a lot !!! Hooooo yes it is !
So easy to stress test elec. with handlebar
It always call me for :
Sorry I finally reply here @rey8801 ^^
thanks a lot mate !
But finally, it’s easier with a wired system (no charge needed) and behind the handlebar, you almost only play on/off on the throttle. I find a sweet parameter spot and order a left thumb throttle that I use reverse on the right for the index finger, works lot better than using thumb!!
But it’s not as easy.
Now it will be, working with a longboard deck :
I hope I have fully answered your questions, do not hesitate if you need more !
Good WE all
Thanks a lot for all the info!
Ok so direct wiring for the remote. Better with finger than with thumb. Got it.
For the brakes I was think of using mechanical ones. I have seen some scooter using them. Or maybe a mix with mechanical in front and regenerative at the back. Like thumb for the throttle and lever for braking.
Another concern is about the motor. Do you think single motor is enough? I mean I want power . I like to keep it medium size and usable but has to be a silent beast. In Esk8 we all go dual at least. So I wondering whether I will get more power out of a single rear motor (6384 up to 80100 depends how well integrated I can get it) or dual hub motors front and rear?
I build one (it’s 2/3 done) with a kickscooter frame, it only had space for 8s and used one hub motor in the wheel, surprisingly strong I’ll finish it as a project at work, my gf does not want it, she doesn’t feel safe
Yes please make a build thread about it.
I would plan the same ! front disk brake and regenerative rear.
The only PB for me, on my setup, is I don’t see/know how I could set the front one on mine without weld support on the fork (what I’m not able to do alone). But I can easily set one in the custom rear harm, on the opposite side of the transmission
It was already to much for my love ^^ Its why I passed then in Foc mode and more speed than torque (when we were both ridding - me on eMTBoard, I was kidding with here at a stop line, she let the dirt go without her, surprised by the torque )
The BLDC mode with 6374 170kV but 6.25:1 ratio was really fun ! My little YZ !
Then FOC 130kV 4.67:1 was a bit less torquey, and the power comes latter. Or I have to be around some speed to get the kick-ass effect of the full throttle.
If you want power you have to sacrifice some speed in single setup yes.
The bigger ratio with the lower kV motor (6384 min) and calculate the max speed acceptable for you, it’s how I made it. (Also I was running lipo 12Ah at 15C you run your ESC at the max batt max recommended … and even a bit more if it’s outside.)
Yeah, so belt should be the thing for you. Chain is not for you
Or like you say maybe 2 good hub motor will even better and quieter ! Mostly for city ride. I’m mostly AT and from what I have tested, geared are always torquier than hubs, but here comparing a dual hub vs single geared motor, I can really say. (but all that without speaking about specific hub scooter motor that I dont know.)
Personally I will advise 9" min ^^ wheel and tire are your only suspension here (just IMO for confort).
no of course for the disk brake only in case they were already installed.
I see for the power. Top speed doesn’t have to be crazy but torque, insane level is about right. Since you have the handle bar you can really race against someone with it hahahaha
Maybe then 8080 or 80100 single motor would be better and enough?
It’s what I hope to verify soon enough ^^
yeah, really, like I say on the 1st post, a little guy with a single esk8, we make a little ride together, going race mode was funny we get totally different setup but almost the same top speed.
Really easy to stress test elec. with the handlebar! full throttle all the time
yeh the video is what made me think about escooter.
Hey @visnu777, how are your projects going? Are you till working on it?
And @rey8801 still working on an e-scooter too ?!
Last night, I start again to be unfaithful to my esk8 gears
The Vostok 1 electric scooter! A 10kw Russian Juggernaut!
https://youtu.be/q6UiMinu3JgВосток-1
Восток-1 acceleration. From Russia with Love!
Don’t tell me about the escooter. Waited 2 months for the delivery and then the parcel (40kg one) got “lost” at the custom in Poland. Got fedup about it and let it go for the moment
Of course I had already set up everything to for when it should have came in.
arg … sorry mate, wish you to get it asap!
Yes, that is the one ! Thanks for sharing Alberto.
I’m thinking about 16s around 6-8p, vesc 6, a good big hub-motor for 10/11" wheels, all AL CNC, 4 suspensions, disk brake, etc. All the rest like the reference ^^
Definitely want to make his lil’bro !
Got it running but its still missing a nice enclosure. My beloved didn’t like the feel of it, she said it feels insecure so now I’ll use it at work. Have to bring it there after the Corona shutdown I actually like it, its a fun thing but not good for longer trips The hub motor had surprisingly good torque at 8s and 15A.
Wow, thats a lightweight one !! Nice slim and slick DIY
8s, 15A with VESC ? You need a buildlog too want to know more !
I play a bit more :
guess I’m gonna need to get my scooter out of the closet
needs new motor, electronics, battery
originally lead acid with brushed motor
My first try at an esk8 before I knew you all existed
Basically a revel scooter skateboard kit.
Professional deck maker, watch your back @jamie
No is gone. Got reimbursed and that’s it. I like your plan. You should get in the beta tester for the new vesc Lacroix is realising. Perfect since they are looking for 16s plus candidates
I can’t compete!!