My kids card to me, they know me well
3 Likes
Can we please have a glamor shot of the offset drive motor mounts? I know they are every day bargin bin parts (dime for 13 etc ),im just a fan of the asterics. Sweet board!! 
2 Likes
it is the magic smoke that makes them dangerous ! I have found that once you free this smoke demon from the said Chineesium electronics ,they are rendered harmless,stationary and not much fun.
Im not sure how they trap the smoke in there but i have gotten pretty good at freeing the smoke demons #freesomkedemons #letmysmokedemonsGO! #fucktaylorswift
1 Like
Running a fardriver on mine (nd72680)
1 Like
What did you have to do to not lose display, turn signals, etc? Been looking to swap a FarDriver into my onyx eventually but there is dangerously little info I can find
1 Like
What controller does this use? I was looking at doing something similar for underglow lights but dont know where to start.
Car LED Light Strip, KaiDengZhe Car LED Headlight Surface Strip Tube Light RGB Multi Color APP Control 23.6 Inch Flexible LED Daytime Running Light Strip Neon -2PCS Amazon.com
I’m using these ones that are marketed as headlight LEDs. Just runs off of 12v and bluetooths to your phone. There are an insane amount of modes. I made it to 200 before I quit playing around.
2 Likes
It’s pretty easy honestly. Way easier to tune than the Kelly that comes on the onyx (I have the smaller Kelly 200a kls on my super).
I don’t run a display or turns. Just controllable dual headlights and a rear tail light that has motion sensors so it automatically lights up brighter when braking. For speed I use this app called “speedometer” screen shot:
There are a few named that but after lots of testing I found that this one with the “72” in the logo is the most accurate. It waits while your at speed before showing the current speed. Distance is way off but I’ve never seen the top speed be off not even by 1mph.
Battery I check off my bms app but 20S at 59AH gets me pretty far haha
I have to do some electrical stuff on the surron to do I should do an install/tune video for the far driver. I have to reco just redoing your whole wiring harness. Stock stuff is under spec and just complicates it imo.
Yessss exactly. Thanks for all the info man
1 Like
i mean yeh chinese invented fireworks and gunpowder. just a spot welder not like im using an AliExpress skydiving parachute loll 
Of course! Have you tuned the stock kelly controller at all? If you have a batt that can push 300a it can be quite a good controller. The usual stock onyx tune is less than 50% that controllers peak settings. I would swap to a QS8 connectors off batt, mount it externally and throw some statorade in the hub if you are going to up the settings too. External mount isn’t 100% needed but helps with cooling a lot if you are throttle happy.
1 Like
I downloaded the motormed app but havent had time to play around with it yet. Is that the best one to access it with? I have the 41Ah battery so I’m sure I could drain it faster after I swap out the connectors and get rid of the discharge fuse.
1 Like
that’s a fucking animal
3 Likes
That’s what I was thinking too. Things a beast.
1 Like
I’ll get back to you in a few days when I’m back in the states I forget which one I ended up going with only tuned it twice ha
That batt should be good for a bit more juice for sure
1 Like
Did you change the battery?
Nah, I modded it to take the CyberTech throttle that the OSSR remote uses, aka the best throttle in esk8 hands down. Throttle alone retails for $80
3 Likes
Oh, I see it now! 
1 Like
Has it really been 4 years here?
2 Likes
i wouldnt know a good spot welder from a shite one. No judgement from the special needs corner