šŸ–¼ Reply to ā€œPictures and nothing elseā€ thread 2023

Media
,
#4543

These arenā€™t obtainable by chance are they?

1 Like
#4544

Only one or two sets of these around.

#4545

Are there files available if I were inclined to make my own?

I have an avio collecting dust because no gears :frowning:

I just need the wheel gears. Those are the specialized cut.

#4546

Good luck getting somewhere to make herringbone gears

2 Likes
#4547

Itā€™s really not that bad. If anyone just added a central runout groove to a herringbone gear, the tool wouldnā€™t collide with the other spur set.

You can also interlock two opposite spur gears and just leave a small gap in between to allow for clearance.

Wust patented a neat herringbone design that offsets the spur pattern so that there is a gap for this as well. Honestly shocked no one has put out a 2 spur herringbone setup with how thin our gear drives have gotten. Bet Apex is on it.

6 Likes
#4548

@Tony_Stark

please tell me these will be on your website soon :pleading_face:
i literally just checked your website yesterday to see if you had 6355s available
settled for maytechs cause i couldnā€™t find em but iā€™ll snag 4 soon as theyā€™re up :eyes:

1 Like
#4549

They are! Only 3 sets on hand thoughā€¦

#4550

ah poop

Iā€™ll keep an eye out for if/when more are in stock :smiling_face_with_three_hearts:
what kv will they be?

1 Like
#4551

Got 1 pair of 175kv and 2 pairs of 205kv in stock. Will be sticking with those kv

2 Likes
#4552

perfect :smiling_face_with_three_hearts:

iā€™ll be waiting!

#4553

wait

you have 2 pairs of 205 kv?

i need 4 motors, thatā€™s, 2 pairs :eyes::eyes::eyes::eyes::eyes::eyes:

[edit]
i may or may not have taken your whole stock of 205kv
iā€™m on coffee

2 Likes
#4554

Youā€™re on coffeešŸ˜‚

Thanks for the order dude Iā€™ll get them shipped out tomorrowšŸ¤™

2 Likes
#4555

hell ya :rofl:

i will further be on coffee arriving home on June 2nd at 1am and trying to put my board together for a ride by 10am the same morning

2 Likes
#4556

@deeznuts_pwned i had one of those, it semeed great when i first tested it then when i went to use it a few months later the welds are absolute shite, no matter how well prepped the electrodes are. Did some research and apparently theyre very dangerously built too - be careful!

1 Like
#4557

yeh most chinese electronics are dangerous, thatā€™s half the fun of using them. :firecracker: :fire: :fire_extinguisher: :+1: :ok_hand:

#4558

My kids card to me, they know me well

3 Likes
#4559

Can we please have a glamor shot of the offset drive motor mounts? I know they are every day bargin bin parts (dime for 13 etc ),im just a fan of the asterics. Sweet board!! :fist: :metal: :call_me_hand:

2 Likes
#4560

it is the magic smoke that makes them dangerous ! I have found that once you free this smoke demon from the said Chineesium electronics ,they are rendered harmless,stationary and not much fun.
Im not sure how they trap the smoke in there but i have gotten pretty good at freeing the smoke demons #freesomkedemons #letmysmokedemonsGO! #fucktaylorswift

1 Like
#4561

Running a fardriver on mine (nd72680)

1 Like
#4562

What did you have to do to not lose display, turn signals, etc? Been looking to swap a FarDriver into my onyx eventually but there is dangerously little info I can find

1 Like