/* Copyright 2016 - 2022 Benjamin Vedder benjamin@vedder.se This file is part of the VESC firmware. The VESC firmware is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. The VESC firmware is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ #ifndef HW_SBX_H_ #define HW_SBX_H_ //SBX is a VESC6.6 dervivative #define HW_NAME "SBX" #define HW_MAJOR 6 #define HW_MINOR 0 // HW properties #define HW_HAS_DRV8301 #define HW_HAS_3_SHUNTS #define HW_HAS_PHASE_SHUNTS #define HW_HAS_PERMANENT_NRF // Macros #define ENABLE_GATE() palSetPad(GPIOB, 5) #define DISABLE_GATE() palClearPad(GPIOB, 5) #define DCCAL_ON() #define DCCAL_OFF() #define IS_DRV_FAULT() (!palReadPad(GPIOB, 12)) #define LED_GREEN_ON() palSetPad(GPIOB, 0) #define LED_GREEN_OFF() palClearPad(GPIOB, 0) #define LED_RED_ON() palSetPad(GPIOB, 1) #define LED_RED_OFF() palClearPad(GPIOB, 1) #define CURRENT_FILTER_ON() palSetPad(GPIOD, 2) #define CURRENT_FILTER_OFF() palClearPad(GPIOD, 2) #define NRF24L_ENABLE() palSetPad(GPIOC, 13) #define NRF24L_DISABLE() palClearPad(GPIOC, 13) /* * ADC Vector * * 0: IN0 SENS1 * 1: IN1 SENS2 * 2: IN2 SENS3 * 3: IN10 CURR1 * 4: IN11 CURR2 * 5: IN12 CURR3 * 6: IN5 ADC_EXT1 * 7: IN6 ADC_EXT2 * 8: IN3 TEMP_PCB * 9: IN14 TEMP_MOTOR * 10: IN15 ADC_EXT3, Shutdown on MK3 * 11: IN13 AN_IN * 12: Vrefint * 13: IN0 SENS1 * 14: IN1 SENS2 */ #define HW_ADC_INJ_CHANNELS 3 #define HW_ADC_NBR_CONV 5 #define HW_ADC_CHANNELS (HW_ADC_NBR_CONV * 3) // ADC Indexes #define ADC_IND_SENS1 3 #define ADC_IND_SENS2 4 #define ADC_IND_SENS3 5 #define ADC_IND_CURR1 0 #define ADC_IND_CURR2 1 #define ADC_IND_CURR3 2 #define ADC_IND_VIN_SENS 11 #define ADC_IND_EXT 6 #define ADC_IND_EXT2 7 #define ADC_IND_TEMP_MOS 8 #define ADC_IND_TEMP_MOTOR 9 #define ADC_IND_VREFINT 12 //#define ADC_IND_SHUTDOWN 10 // ---------------------------- // ADC macros and settings #define CURRENT_SHUNT_RES 0.001 // Component parameters (can be overridden) #define V_REG 3.3 #define VIN_R1 39000.0 #define VIN_R2 2200.0 #define CURRENT_AMP_GAIN 20.0 // Input voltage #define GET_INPUT_VOLTAGE() ((V_REG / 4095.0) * (float)ADC_Value[ADC_IND_VIN_SENS] * ((VIN_R1 + VIN_R2) / VIN_R2)) // NTC Termistors #define NTC_RES(adc_val) ((4095.0 * 10000.0) / adc_val - 10000.0) #define NTC_TEMP(adc_ind) (1.0 / ((logf(NTC_RES(ADC_Value[adc_ind]) / 10000.0) / 3380.0) + (1.0 / 298.15)) - 273.15) #define NTC_RES_MOTOR(adc_val) (10000.0 / ((4095.0 / (float)adc_val) - 1.0)) // Motor temp sensor on low side //#define NTC_TEMP_MOTOR(beta) (1.0 / ((logf(NTC_RES_MOTOR(ADC_Value[ADC_IND_TEMP_MOTOR]) / 10000.0) / beta) + (1.0 / 298.15)) - 273.15) #define NTC_TEMP_MOTOR(beta) (30) // Voltage on ADC channel #define ADC_VOLTS(ch) ((float)ADC_Value[ch] / 4096.0 * V_REG) // Double samples in beginning and end for positive current measurement. // Useful when the shunt sense traces have noise that causes offset. #define CURR1_DOUBLE_SAMPLE 0 #define CURR2_DOUBLE_SAMPLE 0 #define CURR3_DOUBLE_SAMPLE 0 // UART Peripheral to NRF51 for Bluetooth LE #define HW_UART_DEV SD3 #define HW_UART_GPIO_AF GPIO_AF_USART3 #define HW_UART_TX_PORT GPIOB #define HW_UART_TX_PIN 10 #define HW_UART_RX_PORT GPIOB #define HW_UART_RX_PIN 11 // ICU Peripheral for servo decoding for PPM remote - unused #define HW_USE_SERVO_TIM4 #define HW_ICU_TIMER TIM4 #define HW_ICU_TIM_CLK_EN() RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE) #define HW_ICU_DEV ICUD4 #define HW_ICU_CHANNEL ICU_CHANNEL_1 #define HW_ICU_GPIO_AF GPIO_AF_TIM4 #define HW_ICU_GPIO GPIOB #define HW_ICU_PIN 6 // I2C Peripheral - for Nunchuck remote unused #define HW_I2C_DEV I2CD2 #define HW_I2C_GPIO_AF GPIO_AF_I2C2 #define HW_I2C_SCL_PORT GPIOB #define HW_I2C_SCL_PIN 10 #define HW_I2C_SDA_PORT GPIOB #define HW_I2C_SDA_PIN 11 // Hall/encoder pins - unused #define HW_HALL_ENC_GPIO1 GPIOC #define HW_HALL_ENC_PIN1 6 #define HW_HALL_ENC_GPIO2 GPIOC #define HW_HALL_ENC_PIN2 7 #define HW_HALL_ENC_GPIO3 GPIOC #define HW_HALL_ENC_PIN3 8 #define HW_ENC_TIM TIM3 #define HW_ENC_TIM_AF GPIO_AF_TIM3 #define HW_ENC_TIM_CLK_EN() RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE) #define HW_ENC_EXTI_PORTSRC EXTI_PortSourceGPIOC #define HW_ENC_EXTI_PINSRC EXTI_PinSource8 #define HW_ENC_EXTI_CH EXTI9_5_IRQn #define HW_ENC_EXTI_LINE EXTI_Line8 #define HW_ENC_EXTI_ISR_VEC EXTI9_5_IRQHandler #define HW_ENC_TIM_ISR_CH TIM3_IRQn #define HW_ENC_TIM_ISR_VEC TIM3_IRQHandler // SPI pins - used for nRF remote #define HW_SPI_DEV SPID1 #define HW_SPI_GPIO_AF GPIO_AF_SPI1 #define HW_SPI_PORT_NSS GPIOA #define HW_SPI_PIN_NSS 4 #define HW_SPI_PORT_SCK GPIOA #define HW_SPI_PIN_SCK 5 #define HW_SPI_PORT_MOSI GPIOA #define HW_SPI_PIN_MOSI 7 #define HW_SPI_PORT_MISO GPIOA #define HW_SPI_PIN_MISO 6 // SPI for DRV8301 #define DRV8301_MOSI_GPIO GPIOC #define DRV8301_MOSI_PIN 12 #define DRV8301_MISO_GPIO GPIOC #define DRV8301_MISO_PIN 11 #define DRV8301_SCK_GPIO GPIOC #define DRV8301_SCK_PIN 10 #define DRV8301_CS_GPIO GPIOC #define DRV8301_CS_PIN 9 // Measurement macros #define ADC_V_L1 ADC_Value[ADC_IND_SENS1] #define ADC_V_L2 ADC_Value[ADC_IND_SENS2] #define ADC_V_L3 ADC_Value[ADC_IND_SENS3] #define ADC_V_ZERO (ADC_Value[ADC_IND_VIN_SENS] / 2) // Macros #define READ_HALL1() palReadPad(HW_HALL_ENC_GPIO1, HW_HALL_ENC_PIN1) #define READ_HALL2() palReadPad(HW_HALL_ENC_GPIO2, HW_HALL_ENC_PIN2) #define READ_HALL3() palReadPad(HW_HALL_ENC_GPIO3, HW_HALL_ENC_PIN3) // Default setting overrides #define MCCONF_DEFAULT_MOTOR_TYPE MOTOR_TYPE_FOC #define MCCONF_FOC_F_ZV 30000.0 #define MCCONF_L_MAX_ABS_CURRENT 150.0 // The maximum absolute current above which a fault is generated #define MCCONF_FOC_SAMPLE_V0_V7 false // Run control loop in both v0 and v7 (requires phase shunts) // Setting limits #define HW_LIM_CURRENT -120.0, 120.0 #define HW_LIM_CURRENT_IN -120.0, 120.0 #define HW_LIM_CURRENT_ABS 0.0, 160.0 #define HW_LIM_VIN 6.0, 57.0 #define HW_LIM_ERPM -200e3, 200e3 #define HW_LIM_DUTY_MIN 0.0, 0.1 #define HW_LIM_DUTY_MAX 0.0, 0.99 #define HW_LIM_TEMP_FET -40.0, 110.0 #endif /* HW_SBX_H_ */