mmaner
January 14, 2020, 7:28pm
#8719
Honestly, Iāve never ridden either. Iāve had them both in my hands and the TB DDās are made of better quality components. DD is not going to be as fast as Belt Drives, the torque is similar.
Dual Belt Drive values vs. eLofty Dual Direct Drive values
Dual Belt Drive
eLofty Dual Direct Drive
1 Like
nice1. food for thought heh
1 Like
TheFlash
January 14, 2020, 10:07pm
#8721
This is what I got to work with which port would I plug into if I bought it?
1 Like
Ukaz64
January 14, 2020, 10:13pm
#8723
It might be a stupid qestion but whatever. Is it possible to use two different vescās in a dual setup??? Thanks
1 Like
Ukaz64
January 14, 2020, 10:13pm
#8724
I couldnāt find any info about that
b264
January 14, 2020, 10:36pm
#8725
I donāt think thatās true for some ādualā controllers like Unity but I donāt have dual controllers so IDK
b264
January 14, 2020, 10:37pm
#8726
If they are VESC compatible, then yes this is not a problem. If you use CANBUS there are other considerations, but otherwise everything should just work without using CAN.
Use split PWM (āPPMā) or dual PWM (āPPMā)
2 Likes
Ukaz64
January 14, 2020, 10:39pm
#8727
so if i want to connect maytech 4.12 with focbox what should i do? just the CANBUS?
b264
January 14, 2020, 10:42pm
#8728
Do anything except CANBUS
Use split PWM (āPPMā) or dual PWM (āPPMā)
You can actually use CANBUS but youād need to match firmware versions and there are a lot more gotchas
2 Likes
b264
January 14, 2020, 10:44pm
#8730
Ukaz64:
maytech 4.12 with focbox
Realize that one side is going to overheat and throttle down much sooner than the other side though. But this is fine
Ukaz64
January 14, 2020, 10:45pm
#8731
but do i have to make the both settings same?
b264
January 14, 2020, 10:47pm
#8732
No, in fact the settings will be different. The 4.12 probably doesnāt want more than 25A - 30A ābattery maxā while the FOCBOX can do more
The motor numbers should match your motors.
Just set each one up like itās on its own on a single drive skate.
2 Likes
b264
January 14, 2020, 10:48pm
#8733
Limiting the FOCBOX battery max to the same as the 4.12 battery max can make it feel more symmetrical and not pull to one side on hard acceleration
But really torquesteer isnāt that bad, you get used to it in a jiffy just like any other quirk of your board
2 Likes
Ukaz64
January 14, 2020, 10:49pm
#8734
i think of dual setup but one motor on front the other on back so i think it shouldnt be such a problem
1 Like
b264
January 14, 2020, 10:50pm
#8735
Put the FOCBOX on the rear motor, on the heelside of the board
4.12 on front toeside
3 Likes
itsrow
January 14, 2020, 10:51pm
#8737
Anyone here have nothing but problems with the pryside antispark? Today it almost took my battery and my car (lmfao) so itās getting put out of commission but everyone else who has them hasnt had any of the problems Iāve been having.
1 Like
b264
January 14, 2020, 10:56pm
#8738
If youāre doing dual diagonal, I would not even match these. Just run each one to its full ability
1 Like